Всем привет, если есть кто живой в этой теме помогите пожалуйста. Пытаюсь установить прошивку под огненную лампу от грунера и выдает такую ошибку, хотя на версии 1.3 все заливается, вот с 1.4 уже проблемы...
Arduino: 1.8.19 (Windows 10), Плата:"Generic ESP8266 Module, 80 MHz, Flash, Disabled, All SSL ciphers (most compatible), nodemcu, 26 MHz, 40MHz, DOUT (compatible), 1M (64K SPIFFS), 2, nonos-sdk 2.2.1 (legacy), v2 Lower Memory, Disabled, None, Only Sketch, 115200"
In file included from W:\Users\F\Desktop\GyverLamp-master\firmware\GyverLamp_v1.4\GyverLamp_v1.4.ino:122:0:
W:\Users\F\Documents\Arduino\libraries\FastLED/FastLED.h:14:21: note: #pragma message: FastLED version 3.003.002
# pragma message "FastLED version 3.003.002"
^
In file included from W:\Users\F\Documents\Arduino\libraries\FastLED/FastLED.h:65:0,
from W:\Users\F\Desktop\GyverLamp-master\firmware\GyverLamp_v1.4\GyverLamp_v1.4.ino:122:
W:\Users\F\Documents\Arduino\libraries\FastLED/fastspi.h:130:23: note: #pragma message: No hardware SPI pins defined. All SPI access will default to bitbanged output
# pragma message "No hardware SPI pins defined. All SPI access will default to bitbanged output"
^
W:\Users\F\Desktop\GyverLamp-master\firmware\GyverLamp_v1.4\GyverLamp_v1.4.ino: In function 'void setup()':
GyverLamp_v1.4:405:3: error: 'timeClient' was not declared in this scope
timeClient.begin();
^
W:\Users\F\Desktop\GyverLamp-master\firmware\GyverLamp_v1.4\time.ino: In function 'void timeTick()':
time:50:21: error: 'timeClient' was not declared in this scope
timeSynched = timeClient.update() || timeSynched; // если время хотя бы один раз было синхронизировано, продолжаем
^
time:56:33: error: 'localTimeZone' was not declared in this scope
time_t currentLocalTime = localTimeZone.toLocal(timeClient.getEpochTime());
^
W:\Users\F\Desktop\GyverLamp-master\firmware\GyverLamp_v1.4\time.ino: In function 'void getFormattedTime(char*)':
time:176:47: error: 'currentLocalTime' was not declared in this scope
sprintf_P(buf, PSTR("%02u:%02u:%02u"), hour(currentLocalTime), minute(currentLocalTime), second(currentLocalTime));
^
exit status 1
'timeClient' was not declared in this scope
Этот отчёт будет иметь больше информации с
включенной опцией Файл -> Настройки ->
"Показать подробный вывод во время компиляции"
Arduino: 1.8.19 (Windows 10), Плата:"Generic ESP8266 Module, 80 MHz, Flash, Disabled, All SSL ciphers (most compatible), nodemcu, 26 MHz, 40MHz, DOUT (compatible), 1M (64K SPIFFS), 2, nonos-sdk 2.2.1 (legacy), v2 Lower Memory, Disabled, None, Only Sketch, 115200"
In file included from W:\Users\F\Desktop\GyverLamp-master\firmware\GyverLamp_v1.4\GyverLamp_v1.4.ino:122:0:
W:\Users\F\Documents\Arduino\libraries\FastLED/FastLED.h:14:21: note: #pragma message: FastLED version 3.003.002
# pragma message "FastLED version 3.003.002"
^
In file included from W:\Users\F\Documents\Arduino\libraries\FastLED/FastLED.h:65:0,
from W:\Users\F\Desktop\GyverLamp-master\firmware\GyverLamp_v1.4\GyverLamp_v1.4.ino:122:
W:\Users\F\Documents\Arduino\libraries\FastLED/fastspi.h:130:23: note: #pragma message: No hardware SPI pins defined. All SPI access will default to bitbanged output
# pragma message "No hardware SPI pins defined. All SPI access will default to bitbanged output"
^
W:\Users\F\Desktop\GyverLamp-master\firmware\GyverLamp_v1.4\GyverLamp_v1.4.ino: In function 'void setup()':
GyverLamp_v1.4:405:3: error: 'timeClient' was not declared in this scope
timeClient.begin();
^
W:\Users\F\Desktop\GyverLamp-master\firmware\GyverLamp_v1.4\time.ino: In function 'void timeTick()':
time:50:21: error: 'timeClient' was not declared in this scope
timeSynched = timeClient.update() || timeSynched; // если время хотя бы один раз было синхронизировано, продолжаем
^
time:56:33: error: 'localTimeZone' was not declared in this scope
time_t currentLocalTime = localTimeZone.toLocal(timeClient.getEpochTime());
^
W:\Users\F\Desktop\GyverLamp-master\firmware\GyverLamp_v1.4\time.ino: In function 'void getFormattedTime(char*)':
time:176:47: error: 'currentLocalTime' was not declared in this scope
sprintf_P(buf, PSTR("%02u:%02u:%02u"), hour(currentLocalTime), minute(currentLocalTime), second(currentLocalTime));
^
exit status 1
'timeClient' was not declared in this scope
Этот отчёт будет иметь больше информации с
включенной опцией Файл -> Настройки ->
"Показать подробный вывод во время компиляции"