ESP, IoT [MatrixClock] Большие часы 64х32, ESP32

Sergo_ST · 30 Дек 2024

@ASM, Значение вне диапазона, нужно ограничить вот так:

C++:

map(constrain(analogRead(33), 0, 1023), 0, 1023, 200, 10)

ASM · 30 Дек 2024

@Sergo_ST, логика работы у ESP32 иначе, чем у ESP8266))
некоторые моменты, которые работают на 8266, отказываются работать на 32, а то и вовсе вызывают boot loop
вылавливать ошибки приходилось комментируя и раскомментируя по частям...

Старик Похабыч · 30 Дек 2024

А что должно быть ? у тебя 4095 выходит за рамки диапазона 0 -1023,

ASM · 30 Дек 2024

@Старик Похабыч, о, какие люди) давно вас не видел)
с constrain все работает как надо)

ASM · 2 Янв 2025

Зарелизил новую версию)

GitHub - Serega88kos/MatrixClock

Contribute to Serega88kos/MatrixClock development by creating an account on GitHub.

github.com

В ЛС предлагали мне помочь с другим похожим проектом, поэтому жду предложений о совместных разработках и дополнений)
Поле для творчества большое)
Думаю можно сделать и различные интерфейсы на дисплее...

П.С. Меня с ДР))

kym13 · 2 Янв 2025

@ASM, На этом месте IDE зависает намертво, плата как на скрине, версия ядра 2.0.15, библиотеки ваши, уже IDE по новой установил ничего не помогает, ошибку не показывает просто виснет что может быть?

....или переустанови текущую... Так собственно и сделал удалил 2.0 и переустановил 19

ASM · 2 Янв 2025

@kym13, тут походу проблема с программой...
у меня похожее было год назад, когда были две версии, 1.8.19 и 2.0.
попробуй последнюю IDE установить, или переустанови текущую, удалив все предыдущие версии...

Rushns · 30 Янв 2025

А как прикрутить в этот проект кириллицу? может кто уже делал?

ASM · 30 Янв 2025

@Rushns, уведомление только что пришло))
А в чем собственно проблема?) На дисплее отображается кириллица...

Rushns · 31 Янв 2025

Хочу дни недели добавить, а возможно еще и месяцы.. (текстом выводить)

Пробовал эту библиотеку:

GitHub - immortalserg/AdafruitGFXRusFonts

Contribute to immortalserg/AdafruitGFXRusFonts development by creating an account on GitHub.

github.com

Выводит коряво.. может есть у кого красивый шрифт высотой 7-8 пикселей?

Наткнулся на программку https://www.radiokot.ru/artfiles/6741/
Импортировал виндовый шрифт system и сохранил в формате для проекта, буду пробовать..

wulf · 2 Фев 2025

ни кто не упирался в такое ? даж не знаю куда капать

C++:

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\hub.ino:1:12: error: variable or field 'build' declared void
 void build(gh::Builder& b) {
            ^~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\hub.ino:1:12: error: 'gh' has not been declared
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\hub.ino:1:25: error: 'b' was not declared in this scope
 void build(gh::Builder& b) {
                         ^
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino: In function 'void Clock()':
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:2:3: error: 'hour' was not declared in this scope
   hour = ntp.hour();
   ^~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:2:10: error: 'ntp' was not declared in this scope
   hour = ntp.hour();
          ^~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:8:23: error: 'old_time' was not declared in this scope
   if (ntp.minute() != old_time) {
                       ^~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:8:23: note: suggested alternative: 'adjtime'
   if (ntp.minute() != old_time) {
                       ^~~~~~~~
                       adjtime
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:9:5: error: 'display' was not declared in this scope
     display->fillRect(0, 12, 30, 31, black);
     ^~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:9:5: note: suggested alternative: 'delay'
     display->fillRect(0, 12, 30, 31, black);
     ^~~~~~~
     delay
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:9:38: error: 'black' was not declared in this scope
     display->fillRect(0, 12, 30, 31, black);
                                      ^~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:9:38: note: suggested alternative: 'Clock'
     display->fillRect(0, 12, 30, 31, black);
                                      ^~~~~
                                      Clock
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:13:3: error: 'display' was not declared in this scope
   display->setFont(&asm_19x11);
   ^~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:13:3: note: suggested alternative: 'delay'
   display->setFont(&asm_19x11);
   ^~~~~~~
   delay
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:13:21: error: 'asm_19x11' was not declared in this scope
   display->setFont(&asm_19x11);
                     ^~~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:14:8: error: 'flag_night' was not declared in this scope
   if (!flag_night) display->setTextColor(ColorTable[col.clock]);
        ^~~~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:14:8: note: suggested alternative: '_daylight'
   if (!flag_night) display->setTextColor(ColorTable[col.clock]);
        ^~~~~~~~~~
        _daylight
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:14:42: error: 'ColorTable' was not declared in this scope
   if (!flag_night) display->setTextColor(ColorTable[col.clock]);
                                          ^~~~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:14:53: error: 'col' was not declared in this scope
   if (!flag_night) display->setTextColor(ColorTable[col.clock]);
                                                     ^~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:14:53: note: suggested alternative: 'cosl'
   if (!flag_night) display->setTextColor(ColorTable[col.clock]);
                                                     ^~~
                                                     cosl
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:24:3: error: 'old_time' was not declared in this scope
   old_time = m;
   ^~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:24:3: note: suggested alternative: 'adjtime'
   old_time = m;
   ^~~~~~~~
   adjtime
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino: In function 'void ClockNG()':
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:29:10: error: 'flag_night' was not declared in this scope
     if (!flag_night) display->drawPixel(i, 0, display->color444(random(0, 255), random(0, 255), random(0, 255)));
          ^~~~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:29:10: note: suggested alternative: '_daylight'
     if (!flag_night) display->drawPixel(i, 0, display->color444(random(0, 255), random(0, 255), random(0, 255)));
          ^~~~~~~~~~
          _daylight
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:29:22: error: 'display' was not declared in this scope
     if (!flag_night) display->drawPixel(i, 0, display->color444(random(0, 255), random(0, 255), random(0, 255)));
                      ^~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:29:22: note: suggested alternative: 'delay'
     if (!flag_night) display->drawPixel(i, 0, display->color444(random(0, 255), random(0, 255), random(0, 255)));
                      ^~~~~~~
                      delay
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:30:10: error: 'flag_night' was not declared in this scope
     if (!flag_night) display->drawPixel(i, 31, display->color444(random(0, 255), random(0, 255), random(0, 255)));
          ^~~~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:30:10: note: suggested alternative: '_daylight'
     if (!flag_night) display->drawPixel(i, 31, display->color444(random(0, 255), random(0, 255), random(0, 255)));
          ^~~~~~~~~~
          _daylight
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:30:22: error: 'display' was not declared in this scope
     if (!flag_night) display->drawPixel(i, 31, display->color444(random(0, 255), random(0, 255), random(0, 255)));
                      ^~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:30:22: note: suggested alternative: 'delay'
     if (!flag_night) display->drawPixel(i, 31, display->color444(random(0, 255), random(0, 255), random(0, 255)));
                      ^~~~~~~
                      delay
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:33:10: error: 'flag_night' was not declared in this scope
     if (!flag_night) display->drawPixel(0, j, display->color444(random(0, 255), random(0, 255), random(0, 255)));
          ^~~~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:33:10: note: suggested alternative: '_daylight'
     if (!flag_night) display->drawPixel(0, j, display->color444(random(0, 255), random(0, 255), random(0, 255)));
          ^~~~~~~~~~
          _daylight
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:33:22: error: 'display' was not declared in this scope
     if (!flag_night) display->drawPixel(0, j, display->color444(random(0, 255), random(0, 255), random(0, 255)));
                      ^~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:33:22: note: suggested alternative: 'delay'
     if (!flag_night) display->drawPixel(0, j, display->color444(random(0, 255), random(0, 255), random(0, 255)));
                      ^~~~~~~
                      delay
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:34:10: error: 'flag_night' was not declared in this scope
     if (!flag_night) display->drawPixel(63, j, display->color444(random(0, 255), random(0, 255), random(0, 255)));
          ^~~~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:34:10: note: suggested alternative: '_daylight'
     if (!flag_night) display->drawPixel(63, j, display->color444(random(0, 255), random(0, 255), random(0, 255)));
          ^~~~~~~~~~
          _daylight
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:34:22: error: 'display' was not declared in this scope
     if (!flag_night) display->drawPixel(63, j, display->color444(random(0, 255), random(0, 255), random(0, 255)));
                      ^~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:34:22: note: suggested alternative: 'delay'
     if (!flag_night) display->drawPixel(63, j, display->color444(random(0, 255), random(0, 255), random(0, 255)));
                      ^~~~~~~
                      delay
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:36:7: error: 'flag_night' was not declared in this scope
   if (flag_night) display->drawRect(0, 0, 64, 32, black);
       ^~~~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:36:7: note: suggested alternative: '_daylight'
   if (flag_night) display->drawRect(0, 0, 64, 32, black);
       ^~~~~~~~~~
       _daylight
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:36:19: error: 'display' was not declared in this scope
   if (flag_night) display->drawRect(0, 0, 64, 32, black);
                   ^~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:36:19: note: suggested alternative: 'delay'
   if (flag_night) display->drawRect(0, 0, 64, 32, black);
                   ^~~~~~~
                   delay
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:36:51: error: 'black' was not declared in this scope
   if (flag_night) display->drawRect(0, 0, 64, 32, black);
                                                   ^~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:36:51: note: suggested alternative: 'Clock'
   if (flag_night) display->drawRect(0, 0, 64, 32, black);
                                                   ^~~~~
                                                   Clock
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:37:3: error: 'hour' was not declared in this scope
   hour = ntp.hour();
   ^~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:37:10: error: 'ntp' was not declared in this scope
   hour = ntp.hour();
          ^~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:43:23: error: 'old_time' was not declared in this scope
   if (ntp.minute() != old_time) {
                       ^~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:43:23: note: suggested alternative: 'adjtime'
   if (ntp.minute() != old_time) {
                       ^~~~~~~~
                       adjtime
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:44:5: error: 'display' was not declared in this scope
     display->fillRect(0, 12, 30, 31, black);
     ^~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:44:5: note: suggested alternative: 'delay'
     display->fillRect(0, 12, 30, 31, black);
     ^~~~~~~
     delay
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:44:38: error: 'black' was not declared in this scope
     display->fillRect(0, 12, 30, 31, black);
                                      ^~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:44:38: note: suggested alternative: 'Clock'
     display->fillRect(0, 12, 30, 31, black);
                                      ^~~~~
                                      Clock
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:48:3: error: 'display' was not declared in this scope
   display->setFont(&asm_19x11);
   ^~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:48:3: note: suggested alternative: 'delay'
   display->setFont(&asm_19x11);
   ^~~~~~~
   delay
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:48:21: error: 'asm_19x11' was not declared in this scope
   display->setFont(&asm_19x11);
                     ^~~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:50:8: error: 'flag_night' was not declared in this scope
   if (!flag_night) display->setTextColor(display->color444(random(0, 255), random(0, 255), random(0, 255)));
        ^~~~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:50:8: note: suggested alternative: '_daylight'
   if (!flag_night) display->setTextColor(display->color444(random(0, 255), random(0, 255), random(0, 255)));
        ^~~~~~~~~~
        _daylight
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:53:8: error: 'flag_night' was not declared in this scope
   if (!flag_night) display->setTextColor(display->color444(random(0, 255), random(0, 255), random(0, 255)));
        ^~~~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:53:8: note: suggested alternative: '_daylight'
   if (!flag_night) display->setTextColor(display->color444(random(0, 255), random(0, 255), random(0, 255)));
        ^~~~~~~~~~
        _daylight
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:56:8: error: 'flag_night' was not declared in this scope
   if (!flag_night) display->setTextColor(display->color444(random(0, 255), random(0, 255), random(0, 255)));
        ^~~~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:56:8: note: suggested alternative: '_daylight'
   if (!flag_night) display->setTextColor(display->color444(random(0, 255), random(0, 255), random(0, 255)));
        ^~~~~~~~~~
        _daylight
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:59:8: error: 'flag_night' was not declared in this scope
   if (!flag_night) display->setTextColor(display->color444(random(0, 255), random(0, 255), random(0, 255)));
        ^~~~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:59:8: note: suggested alternative: '_daylight'
   if (!flag_night) display->setTextColor(display->color444(random(0, 255), random(0, 255), random(0, 255)));
        ^~~~~~~~~~
        _daylight
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:62:3: error: 'old_time' was not declared in this scope
   old_time = m;
   ^~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:62:3: note: suggested alternative: 'adjtime'
   old_time = m;
   ^~~~~~~~
   adjtime
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino: At global scope:
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:66:8: error: 'gh' does not name a type
 static gh::Timer dots(500);
        ^~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino: In function 'void Dots()':
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:68:7: error: 'dots' was not declared in this scope
   if (dots) {
       ^~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:68:7: note: suggested alternative: 'dot'
   if (dots) {
       ^~~~
       dot
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:70:5: error: 'display' was not declared in this scope
     display->setFont(&asm_19x11);
     ^~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:70:5: note: suggested alternative: 'delay'
     display->setFont(&asm_19x11);
     ^~~~~~~
     delay
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:70:23: error: 'asm_19x11' was not declared in this scope
     display->setFont(&asm_19x11);
                       ^~~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:73:12: error: 'flag_night' was not declared in this scope
       if (!flag_night) display->setTextColor(display->color444(random(0, 255), random(0, 255), random(0, 255)));
            ^~~~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:73:12: note: suggested alternative: '_daylight'
       if (!flag_night) display->setTextColor(display->color444(random(0, 255), random(0, 255), random(0, 255)));
            ^~~~~~~~~~
            _daylight
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:77:29: error: 'black' was not declared in this scope
       display->setTextColor(black);
                             ^~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:77:29: note: suggested alternative: 'Clock'
       display->setTextColor(black);
                             ^~~~~
                             Clock
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino: In function 'void rezhim()':
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:85:10: error: 'gh' does not name a type
   static gh::Timer Ttime(o.interval * 1000);
          ^~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:86:7: error: 'Ttime' was not declared in this scope
   if (Ttime) {
       ^~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:86:7: note: suggested alternative: 'ctime'
   if (Ttime) {
       ^~~~~
       ctime
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:88:5: error: 'display' was not declared in this scope
     display->fillRect(1, 1, 63, 11, black);
     ^~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:88:5: note: suggested alternative: 'delay'
     display->fillRect(1, 1, 63, 11, black);
     ^~~~~~~
     delay
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:88:37: error: 'black' was not declared in this scope
     display->fillRect(1, 1, 63, 11, black);
                                     ^~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:88:37: note: suggested alternative: 'Clock'
     display->fillRect(1, 1, 63, 11, black);
                                     ^~~~~
                                     Clock
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Clock.ino:95:11: error: 'o' was not declared in this scope
       if (o.sens_bme) Hum();
           ^
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino: In function 'void Brightness()':
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:2:10: error: 'gh' does not name a type
   static gh::Timer timer(o.brg * 1000);
          ^~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:3:7: error: 'timer' was not declared in this scope
   if (timer) {
       ^~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:3:7: note: suggested alternative: 'time'
   if (timer) {
       ^~~~~
       time
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:4:9: error: 'o' was not declared in this scope
     if (o.night_mode && ((o.start_night > o.stop_night && (hour >= o.start_night || hour < o.stop_night)) || (o.start_night < o.stop_night && hour >= o.start_night && hour >= o.start_night && hour < o.stop_night))) {
         ^
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:4:60: error: 'hour' was not declared in this scope
     if (o.night_mode && ((o.start_night > o.stop_night && (hour >= o.start_night || hour < o.stop_night)) || (o.start_night < o.stop_night && hour >= o.start_night && hour >= o.start_night && hour < o.stop_night))) {
                                                            ^~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:5:7: error: 'display' was not declared in this scope
       display->setBrightness8(o.night_brg);
       ^~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:5:7: note: suggested alternative: 'delay'
       display->setBrightness8(o.night_brg);
       ^~~~~~~
       delay
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:6:7: error: 'flag_night' was not declared in this scope
       flag_night = true;
       ^~~~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:6:7: note: suggested alternative: '_daylight'
       flag_night = true;
       ^~~~~~~~~~
       _daylight
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:8:7: error: 'flag_night' was not declared in this scope
       flag_night = false;
       ^~~~~~~~~~
C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:8:7: note: suggested alternative: '_daylight'
       flag_night = false;
       ^~~~~~~~~~
       _daylight

wulf · 2 Фев 2025

в одну не влезло

C++:

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:10:24: error: 'new_bright' was not declared in this scope

         if (o.min_max) new_bright = map(constrain(analogRead(BRI_PIN), 0, 1023), 0, 1023, o.min_bright, o.max_bright);   // считать показания с фоторезистора, перевести диапазон

                        ^~~~~~~~~~

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:10:24: note: suggested alternative: 'nearbyint'

         if (o.min_max) new_bright = map(constrain(analogRead(BRI_PIN), 0, 1023), 0, 1023, o.min_bright, o.max_bright);   // считать показания с фоторезистора, перевести диапазон

                        ^~~~~~~~~~

                        nearbyint

In file included from C:\Users\user\AppData\Local\Temp\arduino\sketches\9F9E3FA239EA6201392F6076A8F0553F\sketch\Clock.ino.cpp:1:

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:10:62: error: 'BRI_PIN' was not declared in this scope

         if (o.min_max) new_bright = map(constrain(analogRead(BRI_PIN), 0, 1023), 0, 1023, o.min_bright, o.max_bright);   // считать показания с фоторезистора, перевести диапазон

                                                              ^~~~~~~

C:\Users\user\AppData\Local\Arduino15\packages\esp32\hardware\esp32\2.0.15\cores\esp32/Arduino.h:76:35: note: in definition of macro 'constrain'

#define constrain(amt,low,high) ((amt)<(low)?(low):((amt)>(high)?(high):(amt)))

                                   ^~~

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:10:62: note: the macro 'BRI_PIN' had not yet been defined

         if (o.min_max) new_bright = map(constrain(analogRead(BRI_PIN), 0, 1023), 0, 1023, o.min_bright, o.max_bright);   // считать показания с фоторезистора, перевести диапазон

                                                              ^~~~~~~

C:\Users\user\AppData\Local\Arduino15\packages\esp32\hardware\esp32\2.0.15\cores\esp32/Arduino.h:76:35: note: in definition of macro 'constrain'

#define constrain(amt,low,high) ((amt)<(low)?(low):((amt)>(high)?(high):(amt)))

                                   ^~~

In file included from C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino:4:

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Constants.h:7: note: it was later defined here

#define BRI_PIN 33  // PIN фоторезистора



C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:11:25: error: 'new_bright' was not declared in this scope

         if (!o.min_max) new_bright = map(constrain(analogRead(BRI_PIN), 0, 1023), 0, 1023, o.max_bright, o.min_bright);  // считать показания с фоторезистора, перевести диапазон

                         ^~~~~~~~~~

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:11:25: note: suggested alternative: 'nearbyint'

         if (!o.min_max) new_bright = map(constrain(analogRead(BRI_PIN), 0, 1023), 0, 1023, o.max_bright, o.min_bright);  // считать показания с фоторезистора, перевести диапазон

                         ^~~~~~~~~~

                         nearbyint

In file included from C:\Users\user\AppData\Local\Temp\arduino\sketches\9F9E3FA239EA6201392F6076A8F0553F\sketch\Clock.ino.cpp:1:

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:11:63: error: 'BRI_PIN' was not declared in this scope

         if (!o.min_max) new_bright = map(constrain(analogRead(BRI_PIN), 0, 1023), 0, 1023, o.max_bright, o.min_bright);  // считать показания с фоторезистора, перевести диапазон

                                                               ^~~~~~~

C:\Users\user\AppData\Local\Arduino15\packages\esp32\hardware\esp32\2.0.15\cores\esp32/Arduino.h:76:35: note: in definition of macro 'constrain'

#define constrain(amt,low,high) ((amt)<(low)?(low):((amt)>(high)?(high):(amt)))

                                   ^~~

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:11:63: note: the macro 'BRI_PIN' had not yet been defined

         if (!o.min_max) new_bright = map(constrain(analogRead(BRI_PIN), 0, 1023), 0, 1023, o.max_bright, o.min_bright);  // считать показания с фоторезистора, перевести диапазон

                                                               ^~~~~~~

C:\Users\user\AppData\Local\Arduino15\packages\esp32\hardware\esp32\2.0.15\cores\esp32/Arduino.h:76:35: note: in definition of macro 'constrain'

#define constrain(amt,low,high) ((amt)<(low)?(low):((amt)>(high)?(high):(amt)))

                                   ^~~

In file included from C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino:4:

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Constants.h:7: note: it was later defined here

#define BRI_PIN 33  // PIN фоторезистора



C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:12:64: error: 'new_bright' was not declared in this scope

         Serial.println((String) "Освещенность: " + new_bright);

                                                                ^~~~~~~~~~

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:12:64: note: suggested alternative: 'nearbyint'

         Serial.println((String) "Освещенность: " + new_bright);

                                                                ^~~~~~~~~~

                                                                nearbyint

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:13:9: error: 'display' was not declared in this scope

         display->setBrightness8(new_bright);  // установить новую яркость

         ^~~~~~~

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:13:9: note: suggested alternative: 'delay'

         display->setBrightness8(new_bright);  // установить новую яркость

         ^~~~~~~

         delay

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:15:27: error: 'display' was not declared in this scope

       if (!o.auto_bright) display->setBrightness8(o.min_bright);  // если автояркость выключена, то в расчете минимальная

                           ^~~~~~~

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Brightness.ino:15:27: note: suggested alternative: 'delay'

       if (!o.auto_bright) display->setBrightness8(o.min_bright);  // если автояркость выключена, то в расчете минимальная

                           ^~~~~~~

                           delay

In file included from C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino:4:

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Constants.h: At global scope:

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Constants.h:19:1: error: 'Clock' does not name a type

Clock c;

^~~~~

In file included from C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino:4:

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Constants.h:51:1: error: 'Monitoring' does not name a type

Monitoring m;

^~~~~~~~~~

In file included from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/core/core.h:21,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/core/hub.h:6,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/GyverHub.h:59,

                 from C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino:7:

c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/ui/info.h: In static member function 'static void gh::Info::_build(ghc::InfoCallback, ghc::Packet&, String&, gh::Client&)':

c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/ui/info.h:82:22: error: 'class WiFiClass' has no member named 'getMode'; did you mean 'getSocket'?

         switch (WiFi.getMode()) {

                      ^~~~~~~

                      getSocket

c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/ui/info.h:83:18: error: 'WIFI_AP' was not declared in this scope

             case WIFI_AP:

                  ^~~~~~~

c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/ui/info.h:85:46: error: 'class WiFiClass' has no member named 'softAPIP'

                 p.addString(F("AP_IP"), WiFi.softAPIP().toString());

                                              ^~~~~~~~

c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/ui/info.h:86:48: error: 'class WiFiClass' has no member named 'softAPSSID'

                 p.addString(F("AP_SSID"), WiFi.softAPSSID());

                                                ^~~~~~~~~~

c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/ui/info.h:87:47: error: 'class WiFiClass' has no member named 'softAPmacAddress'; did you mean 'macAddress'?

                 p.addString(F("AP_MAC"), WiFi.softAPmacAddress());

                                               ^~~~~~~~~~~~~~~~

                                               macAddress

c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/ui/info.h:90:18: error: 'WIFI_STA' was not declared in this scope

             case WIFI_STA:

                  ^~~~~~~~

c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/ui/info.h:94:55: error: no matching function for call to 'WiFiClass::macAddress()'

                 p.addString(F("MAC"), WiFi.macAddress());

                                                       ^

In file included from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/ui/info.h:17,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/core/core.h:21,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/core/hub.h:6,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/GyverHub.h:59,

                 from C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino:7:

c:\Users\user\Documents\Arduino\libraries\WiFi\src/WiFi.h:137:14: note: candidate: 'uint8_t* WiFiClass::macAddress(uint8_t*)'

     uint8_t* macAddress(uint8_t* mac);

              ^~~~~~~~~~

c:\Users\user\Documents\Arduino\libraries\WiFi\src/WiFi.h:137:14: note:   candidate expects 1 argument, 0 provided

In file included from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/core/core.h:21,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/core/hub.h:6,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/GyverHub.h:59,

                 from C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino:7:

c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/ui/info.h:97:18: error: 'WIFI_AP_STA' was not declared in this scope

             case WIFI_AP_STA:

                  ^~~~~~~~~~~

c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/ui/info.h:99:46: error: 'class WiFiClass' has no member named 'softAPIP'

                 p.addString(F("AP_IP"), WiFi.softAPIP().toString());

                                              ^~~~~~~~

c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/ui/info.h:100:48: error: 'class WiFiClass' has no member named 'softAPSSID'

                 p.addString(F("AP_SSID"), WiFi.softAPSSID());

                                                ^~~~~~~~~~

c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/ui/info.h:101:47: error: 'class WiFiClass' has no member named 'softAPmacAddress'; did you mean 'macAddress'?

                 p.addString(F("AP_MAC"), WiFi.softAPmacAddress());

                                               ^~~~~~~~~~~~~~~~

                                               macAddress

c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/ui/info.h:104:55: error: no matching function for call to 'WiFiClass::macAddress()'

                 p.addString(F("MAC"), WiFi.macAddress());

                                                       ^

In file included from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/ui/info.h:17,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/core/core.h:21,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/core/hub.h:6,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/GyverHub.h:59,

                 from C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino:7:

c:\Users\user\Documents\Arduino\libraries\WiFi\src/WiFi.h:137:14: note: candidate: 'uint8_t* WiFiClass::macAddress(uint8_t*)'

     uint8_t* macAddress(uint8_t* mac);

              ^~~~~~~~~~

c:\Users\user\Documents\Arduino\libraries\WiFi\src/WiFi.h:137:14: note:   candidate expects 1 argument, 0 provided

In file included from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/esp/sync/http.h:41,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/core/core.h:50,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/core/hub.h:6,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/GyverHub.h:59,

                 from C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino:7:

c:\Users\user\Documents\Arduino\libraries\WebServer\src/WebServer.h: At global scope:

c:\Users\user\Documents\Arduino\libraries\WebServer\src/WebServer.h:177:15: error: cannot declare field 'WebServer::_server' to be of abstract type 'WiFiServer'

   WiFiServer  _server;

               ^~~~~~~

In file included from c:\Users\user\Documents\Arduino\libraries\WiFi\src/WiFi.h:32,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/ui/info.h:17,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/core/core.h:21,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/core/hub.h:6,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/GyverHub.h:59,

                 from C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino:7:

c:\Users\user\Documents\Arduino\libraries\WiFi\src/WiFiServer.h:31:7: note:   because the following virtual functions are pure within 'WiFiServer':

class WiFiServer : public Server {

       ^~~~~~~~~~

In file included from C:\Users\user\AppData\Local\Arduino15\packages\esp32\hardware\esp32\2.0.15\cores\esp32/Arduino.h:194,

                 from C:\Users\user\AppData\Local\Temp\arduino\sketches\9F9E3FA239EA6201392F6076A8F0553F\sketch\Clock.ino.cpp:1:

C:\Users\user\AppData\Local\Arduino15\packages\esp32\hardware\esp32\2.0.15\cores\esp32/Server.h:28:18: note:     'virtual void Server::begin(uint16_t)'

     virtual void begin(uint16_t port=0) =0;

                  ^~~~~

In file included from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/esp/sync/http.h:41,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/core/core.h:50,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/core/hub.h:6,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/GyverHub.h:59,

                 from C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino:7:

c:\Users\user\Documents\Arduino\libraries\WebServer\src/WebServer.h: In member function 'virtual size_t WebServer::_currentClientWrite_P(const char*, size_t)':

c:\Users\user\Documents\Arduino\libraries\WebServer\src/WebServer.h:151:83: error: 'class WiFiClient' has no member named 'write_P'; did you mean 'write'?

   virtual size_t _currentClientWrite_P(PGM_P b, size_t l) { return _currentClient.write_P( b, l ); }

                                                                                   ^~~~~~~

                                                                                   write

In file included from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/core/core.h:50,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/core/hub.h:6,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/GyverHub.h:59,

                 from C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino:7:

c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/esp/sync/http.h: In member function 'virtual void ghc::HubHTTP::begin()':

c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/esp/sync/http.h:314:18: error: 'class WiFiClass' has no member named 'getMode'; did you mean 'getSocket'?

         if (WiFi.getMode() == WIFI_AP || WiFi.getMode() == WIFI_AP_STA) {

                  ^~~~~~~

                  getSocket

c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/esp/sync/http.h:314:31: error: 'WIFI_AP' was not declared in this scope

         if (WiFi.getMode() == WIFI_AP || WiFi.getMode() == WIFI_AP_STA) {

                               ^~~~~~~

c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/esp/sync/http.h:314:47: error: 'class WiFiClass' has no member named 'getMode'; did you mean 'getSocket'?

         if (WiFi.getMode() == WIFI_AP || WiFi.getMode() == WIFI_AP_STA) {

                                               ^~~~~~~

                                               getSocket

c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/esp/sync/http.h:314:60: error: 'WIFI_AP_STA' was not declared in this scope

         if (WiFi.getMode() == WIFI_AP || WiFi.getMode() == WIFI_AP_STA) {

                                                            ^~~~~~~~~~~

c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/esp/sync/http.h:316:37: error: 'class WiFiClass' has no member named 'softAPIP'

             dns.start(53, "*", WiFi.softAPIP());

                                     ^~~~~~~~

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino: At global scope:

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino:30:14: error: 'c' was not declared in this scope

GyverNTP ntp(c.gmt);

              ^

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino:42:48: error: 'c' was not declared in this scope

FileData _clock(&LittleFS, "/clock.dat", 'A', &c, sizeof(c));

                                                ^

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino:42:58: error: 'c' was not declared in this scope

FileData _clock(&LittleFS, "/clock.dat", 'A', &c, sizeof(c));

                                                          ^

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino:44:48: error: 'm' was not declared in this scope

FileData _narod(&LittleFS, "/narod.dat", 'A', &m, sizeof(m));

                                                ^

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino:44:58: error: 'm' was not declared in this scope

FileData _narod(&LittleFS, "/narod.dat", 'A', &m, sizeof(m));

                                                          ^

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino: In function 'void setup()':

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino:65:15: error: 'build' was not declared in this scope

   hub.onBuild(build);  // подключаем билдер

               ^~~~~

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino: In function 'void loop()':

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino:92:7: error: 'm' was not declared in this scope

   if (m.nm_enable) {

       ^

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Monitoring.ino: In function 'void Monitoring()':

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Monitoring.ino:2:8: error: 'class WiFiClass' has no member named 'setAutoReconnect'

   WiFi.setAutoReconnect(true);

        ^~~~~~~~~~~~~~~~

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Monitoring.ino:3:38: error: no matching function for call to 'WiFiClass::macAddress()'

   String buf = "#" + WiFi.macAddress();

                                      ^

In file included from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/ui/info.h:17,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/core/core.h:21,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/core/hub.h:6,

                 from c:\Users\user\Documents\Arduino\libraries\GyverHub-main\src/GyverHub.h:59,

                 from C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\MatrixClock.ino:7:

c:\Users\user\Documents\Arduino\libraries\WiFi\src/WiFi.h:137:14: note: candidate: 'uint8_t* WiFiClass::macAddress(uint8_t*)'

     uint8_t* macAddress(uint8_t* mac);

              ^~~~~~~~~~

c:\Users\user\Documents\Arduino\libraries\WiFi\src/WiFi.h:137:14: note:   candidate expects 1 argument, 0 provided

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Monitoring.ino:5:7: error: 'm' was not declared in this scope

   if (m.nm_tempH) buf = buf + "\n#T1#" + FtempH;

       ^

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Monitoring.ino:6:7: error: 'm' was not declared in this scope

   if (m.nm_tempS) buf = buf + "\n#T2#" + FtempS;

       ^

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Monitoring.ino:7:7: error: 'm' was not declared in this scope

   if (m.nm_pres) buf = buf + "\n#T3#" + Fpres;

       ^

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Monitoring.ino:8:7: error: 'm' was not declared in this scope

   if (m.nm_hum) buf = buf + "\n#T4#" + hum;

       ^

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Sensors.ino: In function 'void ReadSens()':

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Sensors.ino:4:38: error: 'm' was not declared in this scope

     FtempH = bmp.readTemperature() + m.cor_tempH;

                                      ^

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Wifi.ino: In function 'void wifi_connected()':

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Wifi.ino:2:8: error: 'class WiFiClass' has no member named 'mode'

   WiFi.mode(WIFI_STA);

        ^~~~

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Wifi.ino:2:13: error: 'WIFI_STA' was not declared in this scope

   WiFi.mode(WIFI_STA);

             ^~~~~~~~

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Wifi.ino:4:14: error: 'c' was not declared in this scope

   WiFi.begin(c.ssid, c.pass);

              ^

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Wifi.ino:24:10: error: 'class WiFiClass' has no member named 'mode'

     WiFi.mode(WIFI_AP);                     // Меняем режим на режим точки доступа

          ^~~~

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Wifi.ino:24:15: error: 'WIFI_AP' was not declared in this scope

     WiFi.mode(WIFI_AP);                     // Меняем режим на режим точки доступа

               ^~~~~~~

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Wifi.ino:25:10: error: 'class WiFiClass' has no member named 'softAPConfig'

     WiFi.softAPConfig(apIP, apIP, subnet);  // Задаем настройки сети

          ^~~~~~~~~~~~

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Wifi.ino:26:10: error: 'class WiFiClass' has no member named 'softAP'

     WiFi.softAP(ssidAP, passAP);            // Включаем WIFI в режиме точки доступа с именем и паролем

          ^~~~~~

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Wifi.ino:27:17: error: 'build' was not declared in this scope

     hub.onBuild(build);                     // подключаем билдер

                 ^~~~~

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\Wifi.ino:60:17: error: 'build' was not declared in this scope

     hub.onBuild(build);  // подключаем билдер

                 ^~~~~

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\hub.ino: In function 'void build(gh::Builder&)':

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\hub.ino:14:19: error: 'c' was not declared in this scope

           b.Input(c.ssid).label(F("SSID")).attach(&flag_c);

                   ^

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\hub.ino:19:28: error: 'c' was not declared in this scope

           b.Input_("host", c.host).label(F("Сервер NTP")).size(4).attach(&flag_c);

                            ^

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\hub.ino:101:15: error: 'm' was not declared in this scope

           if (m.nm_enable) b.SwitchIcon(&m.nm_enable).label(F("Включен")).fontSize(15).size(1).attach(&flag_monitor);

               ^

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\hub.ino:102:16: error: 'm' was not declared in this scope

           if (!m.nm_enable) b.SwitchIcon(&m.nm_enable).label(F("Выключен")).fontSize(15).size(1).attach(&flag_monitor);

                ^

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\hub.ino:104:20: error: 'm' was not declared in this scope

           b.Input(&m.nm_delay).label(F("Интервал, в сек.")).size(1).attach(&flag_monitor);

                    ^

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\hub.ino:108:25: error: 'm' was not declared in this scope

           b.SwitchIcon(&m.nm_tempH).label(F("Комнатная")).fontSize(15).attach(&flag_monitor);

                         ^

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\hub.ino:117:22: error: 'm' was not declared in this scope

           b.Spinner(&m.cor_tempH).noLabel().range(-9, 9, 0.1, 1).fontSize(15).attach(&flag_monitor);

                      ^

C:\Users\user\Desktop\MatrixClock-main\firmware\Clock\hub.ino:124:22: error: 'm' was not declared in this scope

           b.Spinner(&m.cor_tempS).noLabel().range(-9, 9, 0.1, 1).fontSize(15).attach(&flag_monitor);

                      ^

Несколько библиотек найдено для "WiFi.h"

  Используется: C:\Users\user\Documents\Arduino\libraries\WiFi

  Не используется: C:\Users\user\Documents\Arduino\libraries\WiFiNINA

exit status 1



Compilation error: variable or field 'build' declared void

bort707 · 4 Фев 2025

@wulf,
скобки где-то пропустили или потеряли

Брякомякс · 2 Мар 2025

А какое-нибудь Вики или описание к этому проекту есть? Как у vortigont.

ASM · 2 Мар 2025

@Брякомякс, https://github.com/Serega88kos/MatrixClock/blob/main/README.md

cherezovmax · 7 Май 2025

Всем Доброго! Есть проблема с RGB матрицей прошу помощи-совета. Использую библиотеку pxMatrix https://github.com/2dom/PxMatrix/tree/master?tab=readme-ov-file была куплена матрица и на ней все работало отлично. для след проекта была куплена партия матриц (тесты прогонял на каждой) и вылазит вот такая фигня. Происходит смещение цветов, мерцание пикселей и тд всякие артефакты ВИДЕО Куда смотреть куда копать

bort707 · 8 Май 2025

Матрица на фото так называемая "четырех-скановая" - 64х32 8s
А в предыдущей партии какая была?

ASM · 9 Май 2025

@cherezovmax, попробуй другую библиотеку, а также понизить версию ядра.

cherezovmax · 2 Июн 2025

@bort707, такая же у это го же поставщика с этим же артикулом к сожалению фоток первых экземпляров не осталось но по памяти визуально такие же

bort707 · 2 Июн 2025

Визуально они все одинаковые. Но 4хскановые требуют особой настройки. К сожалекнию, плохо знаю библиотеку pxMatrix, поэтому не знаю, как в ней это настраивается.

cherezovmax · 2 Июн 2025

@ASM,

сейчас используется

cherezovmax · 2 Июн 2025

@bort707, Вот спецификация на эти панели.

bort707 · 2 Июн 2025

cherezovmax написал(а):
спецификация на эти панели.

Простите, но это совершенно "ни о чем".
Никакой полезной информации для вашей проблемы тут нет - типы драйверов не указаны, рисунок распайки светодиодов по рядам отсуствует.
Это и неудивительно - у китайцев и то и другое даже в соседних партиях одной и той же панели может отличаться, а библиотека на разных партиях работает по разному.

Если сможете рассмотреть, напишите типы чипов которые установлены на панели. Там должно быть три разновидности.

Добавка:
Погодите, пока можете чипы не смотреть.
В сообщении #366 на среднем фото на пранели видна наклейка со штрихкодом. Можете снять ее так, чтобы надписи читались?

cherezovmax · 3 Июн 2025

@bort707, В одной партии выявлены 2 разновидности панелей по маркировке глюки прослеживаются на обоих. 1 вариант

Изображение WhatsApp 2025-06-03 в 10.53.55_adb8f678.jpg

Изображение WhatsApp 2025-06-03 в 10.53.56_9df7b41e.jpg

Изображение WhatsApp 2025-06-03 в 10.53.56_efb936c6.jpg

Изображение WhatsApp 2025-06-03 в 10.53.55_07130e19.jpg

cherezovmax · 3 Июн 2025

@bort707, 2 вариант

ESP, IoT [MatrixClock] Большие часы 64х32, ESP32

★★★★★★✩

★★★★★✩✩

★★★★★★★

★★★★★✩✩

★★★★★✩✩

★★★✩✩✩✩

Вложения

★★★★★✩✩

✩✩✩✩✩✩✩

★★★★★✩✩

✩✩✩✩✩✩✩

★✩✩✩✩✩✩

★✩✩✩✩✩✩

★★★★★★★

★✩✩✩✩✩✩

★★★★★✩✩

✩✩✩✩✩✩✩

Вложения

★★★★★★★

★★★★★✩✩

✩✩✩✩✩✩✩

★★★★★★★

✩✩✩✩✩✩✩

✩✩✩✩✩✩✩

Вложения

★★★★★★★

✩✩✩✩✩✩✩

✩✩✩✩✩✩✩